This Brembo performance brake kit is an exact-part-number brake component for the verified 2012-2015 Mercedes-Benz ML63 AMG application listed below. Match manufacturer part number KT00B95, front or rear position, factory brake package, rotor and caliper configuration, wheel clearance, and every application note before ordering.

Key Features

• Prime Ceramic Brake Pads: Minimize noise vibration friction wear and dust emissions for comfortable drives clean wheels and less maintenance.
• High Carbon Cast Iron Discs: Offer higher damping coefficient to reduce vibration noise improve brake response and enhance driving comfort.
• OE-Matching Materials: Use identical high-carbon alloys as original manufacturer production for perfect compatibility and durability.
• Xtra Disc Technology: Special high-carbon alloy tested for greater resistance to thermo-mechanical stress under extreme braking.
• Direct bolt-on replacement no vehicle modifications needed.
• High-carbon construction matches OE standards for longevity.

Fitment

Specifications

What’s Included

One new Brembo product identified by manufacturer part number KT00B95. Rotors, pads, calipers, brackets, lines, sensors, hardware, fluid, tools, and companion service parts are included only when expressly stated for this exact part number.

About Brembo

Brembo develops original-equipment replacement and performance braking components, including rotors, pads, calipers, brake kits, fluid, sensors, and related hardware. Correct selection remains exact-application and exact-part-number specific.

Related Brembo Products

• Brembo KT00572 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Ceramic Pads
• Brembo KT04221 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Low-Met Pads
• Brembo OE 01-03 BMW 525i/97-00 528i/01-03 530i/97-03 540i Rear Disc Brake Kit

Browse the Brembo collection for related brake components.

Frequently Asked Questions

Will this Brembo part fit my 2012-2015 Mercedes-Benz ML63 AMG?
That application is listed, but confirm the front or rear position, factory brake package, rotor diameter and design, caliper type, wheel clearance, production split, and every Brembo application note before ordering.

Should brake components be replaced in axle pairs?
Friction parts are normally serviced in axle sets to maintain balanced braking. Follow the vehicle service procedure and inspect the opposite side, calipers, hoses, hardware, wheel bearings, and brake fluid before installation.

What should be checked before installing this Brembo part?
Compare every component and part number, verify wheel and caliper clearance, inspect mounting and sealing surfaces, measure rotor and hub runout when applicable, use specified torque values, bleed the system correctly, and follow the required bedding procedure.

Installation Instructions

Follow the current Brembo instructions and factory service information for this exact part number. Support the vehicle safely, compare all parts before removal, clean and inspect mounting surfaces, verify runout and wheel clearance, replace one-time hardware and seals as required, use specified torque values, bleed with the correct fluid, check for leaks and free wheel rotation, complete the required bedding procedure, and recheck operation before road use. Professional brake installation is strongly recommended.

This Brembo performance brake kit is an exact-part-number brake component for the verified 2016 Mercedes-Benz C450 AMG 4Matic application listed below. Match manufacturer part number KT00C15, front or rear position, factory brake package, rotor and caliper configuration, wheel clearance, and every application note before ordering.

Key Features

• Complete Rear Kit: Includes two 330mm x 20mm 2-piece floating discs and full pad sets with hardware for straightforward installation.
• Prime Ceramic Brake Pads: Reduce noise and vibration for driving comfort, with low dust emission to keep rims clean and less friction wear for longer life.
• High-Carbon Cast Iron Discs: Offer higher damping to cut vibration and noise, improve brake feel, and provide better heat conduction for quicker cooling.
• Xtra Disc Alloy: Special high-carbon formula resists thermo-mechanical stress for extended durability and sustained performance under heavy use.
• High-carbon Xtra alloy 330mm diameter x 20mm thick 2-piece floating discs paired with Prime ceramic pads.
• OE-Quality Construction: Matches original manufacturer materials for direct replacement, ensuring precise fit and factory-level reliability.

Fitment

Specifications

What’s Included

One new Brembo product identified by manufacturer part number KT00C15. Rotors, pads, calipers, brackets, lines, sensors, hardware, fluid, tools, and companion service parts are included only when expressly stated for this exact part number.

About Brembo

Brembo develops original-equipment replacement and performance braking components, including rotors, pads, calipers, brake kits, fluid, sensors, and related hardware. Correct selection remains exact-application and exact-part-number specific.

Related Brembo Products

• Brembo KT00572 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Ceramic Pads
• Brembo KT04221 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Low-Met Pads
• Brembo OE 01-03 BMW 525i/97-00 528i/01-03 530i/97-03 540i Rear Disc Brake Kit

Browse the Brembo collection for related brake components.

Frequently Asked Questions

Will this Brembo part fit my 2016 Mercedes-Benz C450 AMG 4Matic?
That application is listed, but confirm the front or rear position, factory brake package, rotor diameter and design, caliper type, wheel clearance, production split, and every Brembo application note before ordering.

Should brake components be replaced in axle pairs?
Friction parts are normally serviced in axle sets to maintain balanced braking. Follow the vehicle service procedure and inspect the opposite side, calipers, hoses, hardware, wheel bearings, and brake fluid before installation.

What should be checked before installing this Brembo part?
Compare every component and part number, verify wheel and caliper clearance, inspect mounting and sealing surfaces, measure rotor and hub runout when applicable, use specified torque values, bleed the system correctly, and follow the required bedding procedure.

Installation Instructions

Follow the current Brembo instructions and factory service information for this exact part number. Support the vehicle safely, compare all parts before removal, clean and inspect mounting surfaces, verify runout and wheel clearance, replace one-time hardware and seals as required, use specified torque values, bleed with the correct fluid, check for leaks and free wheel rotation, complete the required bedding procedure, and recheck operation before road use. Professional brake installation is strongly recommended.

This Brembo performance brake kit is an exact-part-number brake component for the verified 2012-2015 Mercedes-Benz ML63 AMG application listed below. Match manufacturer part number KT04496, front or rear position, factory brake package, rotor and caliper configuration, wheel clearance, and every application note before ordering.

Key Features

• High Carbon Cast Iron Discs: Offer strong damping to cut vibration and noise improve brake response boost driving comfort and accelerate heat release.
• OE Material Match: Employs same high carbon materials as factory originals for dependable fit and extended service life.
• Yes it directly replaces rear brakes on 2016-2019 GLE63 AMG 4Matic and S models with 345mm x 28mm high carbon discs and compatible pads.
• Prime Low-Met Pads: Deliver comfort and quality through patented designs matching OE performance standards with complete production oversight.
• Includes all necessary hardware for direct bolt-on fit to stock calipers.
• High carbon cast iron same as OE offering improved damping noise reduction and heat transfer over standard castings.

Fitment

Specifications

What’s Included

One new Brembo product identified by manufacturer part number KT04496. Rotors, pads, calipers, brackets, lines, sensors, hardware, fluid, tools, and companion service parts are included only when expressly stated for this exact part number.

About Brembo

Brembo develops original-equipment replacement and performance braking components, including rotors, pads, calipers, brake kits, fluid, sensors, and related hardware. Correct selection remains exact-application and exact-part-number specific.

Related Brembo Products

• Brembo KT00572 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Ceramic Pads
• Brembo KT04221 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Low-Met Pads
• Brembo OE 01-03 BMW 525i/97-00 528i/01-03 530i/97-03 540i Rear Disc Brake Kit

Browse the Brembo collection for related brake components.

Frequently Asked Questions

Will this Brembo part fit my 2012-2015 Mercedes-Benz ML63 AMG?
That application is listed, but confirm the front or rear position, factory brake package, rotor diameter and design, caliper type, wheel clearance, production split, and every Brembo application note before ordering.

Should brake components be replaced in axle pairs?
Friction parts are normally serviced in axle sets to maintain balanced braking. Follow the vehicle service procedure and inspect the opposite side, calipers, hoses, hardware, wheel bearings, and brake fluid before installation.

What should be checked before installing this Brembo part?
Compare every component and part number, verify wheel and caliper clearance, inspect mounting and sealing surfaces, measure rotor and hub runout when applicable, use specified torque values, bleed the system correctly, and follow the required bedding procedure.

Installation Instructions

Follow the current Brembo instructions and factory service information for this exact part number. Support the vehicle safely, compare all parts before removal, clean and inspect mounting surfaces, verify runout and wheel clearance, replace one-time hardware and seals as required, use specified torque values, bleed with the correct fluid, check for leaks and free wheel rotation, complete the required bedding procedure, and recheck operation before road use. Professional brake installation is strongly recommended.

This Brembo performance brake kit is an exact-part-number brake component for the verified 2016 Mercedes-Benz C450 AMG 4Matic application listed below. Match manufacturer part number KT04513, front or rear position, factory brake package, rotor and caliper configuration, wheel clearance, and every application note before ordering.

Key Features

• High-Carbon Cast Iron Discs: Offer higher damping to cut vibration and noise while improving heat conduction for quicker cooling times.
• Xtra Disc Option Materials: Use special high-carbon alloys tested for resistance to thermo-mechanical stress during heavy braking.
• Prime Low-Met Pads: Provide smooth comfortable braking with performance focus using materials equal to original equipment standards.
• Full Production Control: Brembo manages every stage ensuring consistent quality matching OE specifications for these Mercedes models.
• Boxed for protection ships via ground freight for kits over 25 lbs.
• Includes all necessary hardware pads clip directly to OEM calipers.

Fitment

Specifications

What’s Included

One new Brembo product identified by manufacturer part number KT04513. Rotors, pads, calipers, brackets, lines, sensors, hardware, fluid, tools, and companion service parts are included only when expressly stated for this exact part number.

About Brembo

Brembo develops original-equipment replacement and performance braking components, including rotors, pads, calipers, brake kits, fluid, sensors, and related hardware. Correct selection remains exact-application and exact-part-number specific.

Related Brembo Products

• Brembo KT00572 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Ceramic Pads
• Brembo KT04221 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Low-Met Pads
• Brembo OE 01-03 BMW 525i/97-00 528i/01-03 530i/97-03 540i Rear Disc Brake Kit

Browse the Brembo collection for related brake components.

Frequently Asked Questions

Will this Brembo part fit my 2016 Mercedes-Benz C450 AMG 4Matic?
That application is listed, but confirm the front or rear position, factory brake package, rotor diameter and design, caliper type, wheel clearance, production split, and every Brembo application note before ordering.

Should brake components be replaced in axle pairs?
Friction parts are normally serviced in axle sets to maintain balanced braking. Follow the vehicle service procedure and inspect the opposite side, calipers, hoses, hardware, wheel bearings, and brake fluid before installation.

What should be checked before installing this Brembo part?
Compare every component and part number, verify wheel and caliper clearance, inspect mounting and sealing surfaces, measure rotor and hub runout when applicable, use specified torque values, bleed the system correctly, and follow the required bedding procedure.

Installation Instructions

Follow the current Brembo instructions and factory service information for this exact part number. Support the vehicle safely, compare all parts before removal, clean and inspect mounting surfaces, verify runout and wheel clearance, replace one-time hardware and seals as required, use specified torque values, bleed with the correct fluid, check for leaks and free wheel rotation, complete the required bedding procedure, and recheck operation before road use. Professional brake installation is strongly recommended.

This Brembo performance brake kit is an exact-part-number brake component for the verified 2010-2011 Mercedes-Benz E550 application listed below. Match manufacturer part number KT00A87, front or rear position, factory brake package, rotor and caliper configuration, wheel clearance, and every application note before ordering.

Key Features

• Prime Ceramic Brake Pads: Minimize noise and vibration while reducing friction wear and dust emissions for clean wheel rims and extended service intervals.
• High Carbon Cast Iron Rotors: Provide higher damping to cut vibration and noise improve brake response and enhance heat conduction for quicker cooling times.
• OE Matching Materials: Constructed from identical high carbon content as factory discs for dependable behavior and driving comfort.
• Complete Rear Kit: Includes two rotors and pads with all necessary components for straightforward replacement MPN KT00A87.
• Enhanced Durability: High carbon alloy resists thermo-mechanical stress ensuring longevity under demanding use.
• Bolt-on design uses existing calipers and hardware.

Fitment

Specifications

What’s Included

One new Brembo product identified by manufacturer part number KT00A87. Rotors, pads, calipers, brackets, lines, sensors, hardware, fluid, tools, and companion service parts are included only when expressly stated for this exact part number.

About Brembo

Brembo develops original-equipment replacement and performance braking components, including rotors, pads, calipers, brake kits, fluid, sensors, and related hardware. Correct selection remains exact-application and exact-part-number specific.

Related Brembo Products

• Brembo KT00572 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Ceramic Pads
• Brembo KT04221 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Low-Met Pads
• Brembo OE 01-03 BMW 525i/97-00 528i/01-03 530i/97-03 540i Rear Disc Brake Kit

Browse the Brembo collection for related brake components.

Frequently Asked Questions

Will this Brembo part fit my 2010-2011 Mercedes-Benz E550?
That application is listed, but confirm the front or rear position, factory brake package, rotor diameter and design, caliper type, wheel clearance, production split, and every Brembo application note before ordering.

Should brake components be replaced in axle pairs?
Friction parts are normally serviced in axle sets to maintain balanced braking. Follow the vehicle service procedure and inspect the opposite side, calipers, hoses, hardware, wheel bearings, and brake fluid before installation.

What should be checked before installing this Brembo part?
Compare every component and part number, verify wheel and caliper clearance, inspect mounting and sealing surfaces, measure rotor and hub runout when applicable, use specified torque values, bleed the system correctly, and follow the required bedding procedure.

Installation Instructions

Follow the current Brembo instructions and factory service information for this exact part number. Support the vehicle safely, compare all parts before removal, clean and inspect mounting surfaces, verify runout and wheel clearance, replace one-time hardware and seals as required, use specified torque values, bleed with the correct fluid, check for leaks and free wheel rotation, complete the required bedding procedure, and recheck operation before road use. Professional brake installation is strongly recommended.

This Brembo performance brake kit is an exact-part-number brake component for the verified 2010-2013 Mercedes-Benz E63 AMG application listed below. Match manufacturer part number KT04478, front or rear position, factory brake package, rotor and caliper configuration, wheel clearance, and every application note before ordering.

Key Features

• High Carbon Cast Iron Discs: Offer higher damping coefficient to reduce vibration and noise while improving brake feel and driving comfort.
• Enhanced Heat Conduction: High carbon material transfers heat faster from braking surfaces for shorter cooling times between stops.
• Xtra Disc Alloy: Special high carbon formulation tested for increased resistance to thermo-mechanical stress in high-performance use.
• Full Installation Hardware: Includes all necessary components for simpler safer mounting and direct OE compatibility.
• Prime Low-Met Pads: Deliver comfort and quality with performance focus through patented solutions fully equivalent to OE specifications.
• Bolt-on direct replacement for specified AMG models no vehicle modifications needed.

Fitment

Specifications

What’s Included

One new Brembo product identified by manufacturer part number KT04478. Rotors, pads, calipers, brackets, lines, sensors, hardware, fluid, tools, and companion service parts are included only when expressly stated for this exact part number.

About Brembo

Brembo develops original-equipment replacement and performance braking components, including rotors, pads, calipers, brake kits, fluid, sensors, and related hardware. Correct selection remains exact-application and exact-part-number specific.

Related Brembo Products

• Brembo KT00572 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Ceramic Pads
• Brembo KT04221 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Low-Met Pads
• Brembo OE 01-03 BMW 525i/97-00 528i/01-03 530i/97-03 540i Rear Disc Brake Kit

Browse the Brembo collection for related brake components.

Frequently Asked Questions

Will this Brembo part fit my 2010-2013 Mercedes-Benz E63 AMG?
That application is listed, but confirm the front or rear position, factory brake package, rotor diameter and design, caliper type, wheel clearance, production split, and every Brembo application note before ordering.

Should brake components be replaced in axle pairs?
Friction parts are normally serviced in axle sets to maintain balanced braking. Follow the vehicle service procedure and inspect the opposite side, calipers, hoses, hardware, wheel bearings, and brake fluid before installation.

What should be checked before installing this Brembo part?
Compare every component and part number, verify wheel and caliper clearance, inspect mounting and sealing surfaces, measure rotor and hub runout when applicable, use specified torque values, bleed the system correctly, and follow the required bedding procedure.

Installation Instructions

Follow the current Brembo instructions and factory service information for this exact part number. Support the vehicle safely, compare all parts before removal, clean and inspect mounting surfaces, verify runout and wheel clearance, replace one-time hardware and seals as required, use specified torque values, bleed with the correct fluid, check for leaks and free wheel rotation, complete the required bedding procedure, and recheck operation before road use. Professional brake installation is strongly recommended.

Brembo OE Rear Disc Brake Kit is identified by exact Brembo OE manufacturer part number KT04202 for the application and configuration shown. Confirm the exact manufacturer part number and all current specifications before ordering.

Key Features

• For Xtra discs special alloy high carbon materials are produced and tested to have greater resistance to the thermo-mechanical stress to which the brake disc is subjected.
• Prime low-Met pads ensure comfort and quality, with a specific focus on performance, thanks to patented solutions, full accessories and absolute control of all production stages that aim to make Prime pads equivalent to the OE.

Fitment

Select this component by exact part number, dimensions, engine or system architecture, and mating components. No broad year-make-model claim is used where the manufacturer does not publish one.

Specifications

What’s Included

One new Brembo OE disc brake kit identified by manufacturer part number KT04202 in the configuration shown. Hardware or companion parts are included only when expressly stated by the manufacturer.

About Brembo OE

Brembo OE manufactures automotive performance and replacement parts identified by exact part number, specifications, and published application data.

Related Brembo OE Products

• Shop all Brembo OE products
• Brembo OE Front Disc Brake Kit
• Brembo OE Front Disc Brake Kit
• Brembo OE Rear Disc Brake Kit

Frequently Asked Questions

How do I confirm KT04202 is correct?
Select this component by exact part number, dimensions, engine or system architecture, and mating components. No broad year-make-model claim is used where the manufacturer does not publish one.

Are similar-looking parts interchangeable?
No. Match part number KT04202, dimensions, configuration, included components, and every current manufacturer note.

What is included with this listing?
One new Brembo OE disc brake kit identified by manufacturer part number KT04202 in the configuration shown. Hardware or companion parts are included only when expressly stated by the manufacturer.

Installation

Follow the current Brembo OE instructions for part number KT04202. Verify fit, clearance, system specifications, fastener torque, and safe operation before use. Professional installation is recommended when specialized tools, alignment, calibration, or fabrication are required.

This Brembo performance brake kit is an exact-part-number brake component for the verified 2003 Mercedes-Benz CL500 application listed below. Match manufacturer part number KT00B33, front or rear position, factory brake package, rotor and caliper configuration, wheel clearance, and every application note before ordering.

Key Features

• Prime Ceramic Brake Pads: Minimize noise and vibration for driving comfort while reducing friction wear low dust keeps rims clean with less maintenance.
• High Carbon Cast Iron Discs: Provide higher damping coefficient to cut vibration and noise improve brake response and enhance driving comfort.
• OEM-Matched Materials: Brembo uses identical high carbon materials as original manufacturers for consistent performance and reliability.
• Thermo-Mechanical Resistance: Special alloy high carbon construction withstands stress for longer service life.
• High carbon cast iron same as OEM offers better damping noise reduction and heat dissipation for reliable performance.
• Requires standard tools torque to Mercedes specs for caliper bolts and pads.

Fitment

Specifications

What’s Included

One new Brembo product identified by manufacturer part number KT00B33. Rotors, pads, calipers, brackets, lines, sensors, hardware, fluid, tools, and companion service parts are included only when expressly stated for this exact part number.

About Brembo

Brembo develops original-equipment replacement and performance braking components, including rotors, pads, calipers, brake kits, fluid, sensors, and related hardware. Correct selection remains exact-application and exact-part-number specific.

Related Brembo Products

• Brembo KT00572 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Ceramic Pads
• Brembo KT04221 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Low-Met Pads
• Brembo OE 01-03 BMW 525i/97-00 528i/01-03 530i/97-03 540i Rear Disc Brake Kit

Browse the Brembo collection for related brake components.

Frequently Asked Questions

Will this Brembo part fit my 2003 Mercedes-Benz CL500?
That application is listed, but confirm the front or rear position, factory brake package, rotor diameter and design, caliper type, wheel clearance, production split, and every Brembo application note before ordering.

Should brake components be replaced in axle pairs?
Friction parts are normally serviced in axle sets to maintain balanced braking. Follow the vehicle service procedure and inspect the opposite side, calipers, hoses, hardware, wheel bearings, and brake fluid before installation.

What should be checked before installing this Brembo part?
Compare every component and part number, verify wheel and caliper clearance, inspect mounting and sealing surfaces, measure rotor and hub runout when applicable, use specified torque values, bleed the system correctly, and follow the required bedding procedure.

Installation Instructions

Follow the current Brembo instructions and factory service information for this exact part number. Support the vehicle safely, compare all parts before removal, clean and inspect mounting surfaces, verify runout and wheel clearance, replace one-time hardware and seals as required, use specified torque values, bleed with the correct fluid, check for leaks and free wheel rotation, complete the required bedding procedure, and recheck operation before road use. Professional brake installation is strongly recommended.

This Brembo performance brake kit is an exact-part-number brake component for the verified 2013-2019 Mercedes-Benz SL63 AMG application listed below. Match manufacturer part number KT04538, front or rear position, factory brake package, rotor and caliper configuration, wheel clearance, and every application note before ordering.

Key Features

• High Carbon Cast Iron Discs: Offer higher damping to reduce vibration and noise improve brake response and enhance driving comfort with faster heat transfer for shorter cooling times.
• Complete Installation Hardware: Includes all necessary fixings for simpler safer setup without additional parts.
• OE-Matching Materials: Uses identical high carbon alloys as original manufacturer for proven durability and heat management.
• Prime Low-Met Pads: Deliver comfort quality and focused performance through patented compounds with full production control matching OE standards.
• Includes all OE-style mounting hardware for seamless fitment.
• Discs feature high carbon cast iron for vibration reduction and heat dissipation pads use low-met Prime compound for low dust and strong bite.

Fitment

Specifications

What’s Included

One new Brembo product identified by manufacturer part number KT04538. Rotors, pads, calipers, brackets, lines, sensors, hardware, fluid, tools, and companion service parts are included only when expressly stated for this exact part number.

About Brembo

Brembo develops original-equipment replacement and performance braking components, including rotors, pads, calipers, brake kits, fluid, sensors, and related hardware. Correct selection remains exact-application and exact-part-number specific.

Related Brembo Products

• Brembo KT00572 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Ceramic Pads
• Brembo KT04221 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Low-Met Pads
• Brembo OE 01-03 BMW 525i/97-00 528i/01-03 530i/97-03 540i Rear Disc Brake Kit

Browse the Brembo collection for related brake components.

Frequently Asked Questions

Will this Brembo part fit my 2013-2019 Mercedes-Benz SL63 AMG?
That application is listed, but confirm the front or rear position, factory brake package, rotor diameter and design, caliper type, wheel clearance, production split, and every Brembo application note before ordering.

Should brake components be replaced in axle pairs?
Friction parts are normally serviced in axle sets to maintain balanced braking. Follow the vehicle service procedure and inspect the opposite side, calipers, hoses, hardware, wheel bearings, and brake fluid before installation.

What should be checked before installing this Brembo part?
Compare every component and part number, verify wheel and caliper clearance, inspect mounting and sealing surfaces, measure rotor and hub runout when applicable, use specified torque values, bleed the system correctly, and follow the required bedding procedure.

Installation Instructions

Follow the current Brembo instructions and factory service information for this exact part number. Support the vehicle safely, compare all parts before removal, clean and inspect mounting surfaces, verify runout and wheel clearance, replace one-time hardware and seals as required, use specified torque values, bleed with the correct fluid, check for leaks and free wheel rotation, complete the required bedding procedure, and recheck operation before road use. Professional brake installation is strongly recommended.

This Brembo performance brake kit is an exact-part-number brake component for the verified 2013-2019 Mercedes-Benz SL63 AMG application listed below. Match manufacturer part number KT00C26, front or rear position, factory brake package, rotor and caliper configuration, wheel clearance, and every application note before ordering.

Key Features

• Prime Ceramic Brake Pads: Minimize noise and vibration for driving comfort, reduce friction wear, and emit low dust to keep wheel rims clean with less maintenance.
• High Carbon Cast Iron Discs: Offer higher damping coefficient than standard materials to decrease vibration and noise, improve brake behavior, and enhance driving comfort.
• Xtra Disc Technology: Uses special high carbon alloy materials tested for greater resistance to thermo-mechanical stress on the brake disc.
• OE Matching Materials: Produced with the same high-quality materials as original manufacturer discs for direct compatibility and reliability.
• Complete kit includes two rear brake discs and ceramic pads for straightforward replacement.
• Bolt-on direct replacement for OE rear brakes, no modifications required.

Fitment

Specifications

What’s Included

One new Brembo product identified by manufacturer part number KT00C26. Rotors, pads, calipers, brackets, lines, sensors, hardware, fluid, tools, and companion service parts are included only when expressly stated for this exact part number.

About Brembo

Brembo develops original-equipment replacement and performance braking components, including rotors, pads, calipers, brake kits, fluid, sensors, and related hardware. Correct selection remains exact-application and exact-part-number specific.

Related Brembo Products

• Brembo KT00572 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Ceramic Pads
• Brembo KT04221 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Low-Met Pads
• Brembo OE 01-03 BMW 525i/97-00 528i/01-03 530i/97-03 540i Rear Disc Brake Kit

Browse the Brembo collection for related brake components.

Frequently Asked Questions

Will this Brembo part fit my 2013-2019 Mercedes-Benz SL63 AMG?
That application is listed, but confirm the front or rear position, factory brake package, rotor diameter and design, caliper type, wheel clearance, production split, and every Brembo application note before ordering.

Should brake components be replaced in axle pairs?
Friction parts are normally serviced in axle sets to maintain balanced braking. Follow the vehicle service procedure and inspect the opposite side, calipers, hoses, hardware, wheel bearings, and brake fluid before installation.

What should be checked before installing this Brembo part?
Compare every component and part number, verify wheel and caliper clearance, inspect mounting and sealing surfaces, measure rotor and hub runout when applicable, use specified torque values, bleed the system correctly, and follow the required bedding procedure.

Installation Instructions

Follow the current Brembo instructions and factory service information for this exact part number. Support the vehicle safely, compare all parts before removal, clean and inspect mounting surfaces, verify runout and wheel clearance, replace one-time hardware and seals as required, use specified torque values, bleed with the correct fluid, check for leaks and free wheel rotation, complete the required bedding procedure, and recheck operation before road use. Professional brake installation is strongly recommended.

This Brembo performance brake kit is an exact-part-number brake component for the verified 2012-2016 Mercedes-Benz SLK55 AMG application listed below. Match manufacturer part number KT00484, front or rear position, factory brake package, rotor and caliper configuration, wheel clearance, and every application note before ordering.

Key Features

• Complete OE Replacement Kit: Includes two rear discs (330mm x 22mm vented) and full pad sets for direct bolt-on installation without modifications.
• Prime Ceramic Brake Pads: Minimize noise and vibration while reducing friction wear and low dust emission for clean wheel rims and less maintenance.
• High Carbon Cast Iron Discs: Match original manufacturer materials with higher damping coefficient to decrease vibration, noise, and improve brake behavior plus better heat conduction for faster cooling.
• Xtra Disc Alloy Materials: Special high-carbon formulation tested for greater resistance to thermo-mechanical stress ensuring durability under demanding conditions.
• Enhanced Driving Comfort: Consistent performance across wet, dry, and high-heat scenarios with optimized pad-disc friction pairing.
• High-carbon cast iron discs with special alloy for heat resistance and Prime Ceramic pads for low dust and noise.

Fitment

Specifications

What’s Included

One new Brembo product identified by manufacturer part number KT00484. Rotors, pads, calipers, brackets, lines, sensors, hardware, fluid, tools, and companion service parts are included only when expressly stated for this exact part number.

About Brembo

Brembo develops original-equipment replacement and performance braking components, including rotors, pads, calipers, brake kits, fluid, sensors, and related hardware. Correct selection remains exact-application and exact-part-number specific.

Related Brembo Products

• Brembo KT00572 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Ceramic Pads
• Brembo KT04221 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Low-Met Pads
• Brembo OE 01-03 BMW 525i/97-00 528i/01-03 530i/97-03 540i Rear Disc Brake Kit

Browse the Brembo collection for related brake components.

Frequently Asked Questions

Will this Brembo part fit my 2012-2016 Mercedes-Benz SLK55 AMG?
That application is listed, but confirm the front or rear position, factory brake package, rotor diameter and design, caliper type, wheel clearance, production split, and every Brembo application note before ordering.

Should brake components be replaced in axle pairs?
Friction parts are normally serviced in axle sets to maintain balanced braking. Follow the vehicle service procedure and inspect the opposite side, calipers, hoses, hardware, wheel bearings, and brake fluid before installation.

What should be checked before installing this Brembo part?
Compare every component and part number, verify wheel and caliper clearance, inspect mounting and sealing surfaces, measure rotor and hub runout when applicable, use specified torque values, bleed the system correctly, and follow the required bedding procedure.

Installation Instructions

Follow the current Brembo instructions and factory service information for this exact part number. Support the vehicle safely, compare all parts before removal, clean and inspect mounting surfaces, verify runout and wheel clearance, replace one-time hardware and seals as required, use specified torque values, bleed with the correct fluid, check for leaks and free wheel rotation, complete the required bedding procedure, and recheck operation before road use. Professional brake installation is strongly recommended.

This Brembo performance brake kit is an exact-part-number brake component for the verified 2010-2013 Mercedes-Benz E63 AMG application listed below. Match manufacturer part number KT00B80, front or rear position, factory brake package, rotor and caliper configuration, wheel clearance, and every application note before ordering.

Key Features

• Precise OE Specifications: 330mm diameter x 22mm thick vented rotors with direct bolt-on fit ensure seamless replacement.
• Prime Ceramic Brake Pads: Minimize noise vibration and dust emissions for cleaner wheels and quieter stops with low friction wear.
• High-Carbon Cast Iron Rotors: Provide higher damping to cut vibration noise while enhancing brake feel and driving comfort.
• Complete kit includes 2 rotors and 1 pad set for both rear wheels.
• Direct bolt-on replacement using existing caliper hardware.
• Yes it provides exact OE replacement for 2012 Mercedes-Benz C63 AMG Black Series including 330x22mm rotors and ceramic pads.

Fitment

Specifications

What’s Included

One new Brembo product identified by manufacturer part number KT00B80. Rotors, pads, calipers, brackets, lines, sensors, hardware, fluid, tools, and companion service parts are included only when expressly stated for this exact part number.

About Brembo

Brembo develops original-equipment replacement and performance braking components, including rotors, pads, calipers, brake kits, fluid, sensors, and related hardware. Correct selection remains exact-application and exact-part-number specific.

Related Brembo Products

• Brembo KT00572 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Ceramic Pads
• Brembo KT04221 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Low-Met Pads
• Brembo OE 01-03 BMW 525i/97-00 528i/01-03 530i/97-03 540i Rear Disc Brake Kit

Browse the Brembo collection for related brake components.

Frequently Asked Questions

Will this Brembo part fit my 2010-2013 Mercedes-Benz E63 AMG?
That application is listed, but confirm the front or rear position, factory brake package, rotor diameter and design, caliper type, wheel clearance, production split, and every Brembo application note before ordering.

Should brake components be replaced in axle pairs?
Friction parts are normally serviced in axle sets to maintain balanced braking. Follow the vehicle service procedure and inspect the opposite side, calipers, hoses, hardware, wheel bearings, and brake fluid before installation.

What should be checked before installing this Brembo part?
Compare every component and part number, verify wheel and caliper clearance, inspect mounting and sealing surfaces, measure rotor and hub runout when applicable, use specified torque values, bleed the system correctly, and follow the required bedding procedure.

Installation Instructions

Follow the current Brembo instructions and factory service information for this exact part number. Support the vehicle safely, compare all parts before removal, clean and inspect mounting surfaces, verify runout and wheel clearance, replace one-time hardware and seals as required, use specified torque values, bleed with the correct fluid, check for leaks and free wheel rotation, complete the required bedding procedure, and recheck operation before road use. Professional brake installation is strongly recommended.

This Brembo performance brake kit is an exact-part-number brake component for the verified 2015-2021 Mercedes-Benz C63 AMG S application listed below. Match manufacturer part number KT04492, front or rear position, factory brake package, rotor and caliper configuration, wheel clearance, and every application note before ordering.

Key Features

• High Carbon Cast Iron Discs: Offer higher damping to reduce vibration and noise improve brake behavior and enhance driving comfort with better heat conduction for faster cooling.
• OE-Matching Materials: Brembo uses the same high carbon material as original manufacturers for consistent reliability and durability.
• Xtra Disc Option Ready: Special alloy high carbon construction resists thermo-mechanical stress for extended performance under heavy use.
• Prime Low-Met Pads: Provide comfort and quality with patented solutions focused on performance equivalent to OE through full production control.
• Includes all necessary hardware compatible with OEM calipers no modifications needed.
• High carbon construction reduces noise and improves heat dissipation.

Fitment

Specifications

What’s Included

One new Brembo product identified by manufacturer part number KT04492. Rotors, pads, calipers, brackets, lines, sensors, hardware, fluid, tools, and companion service parts are included only when expressly stated for this exact part number.

About Brembo

Brembo develops original-equipment replacement and performance braking components, including rotors, pads, calipers, brake kits, fluid, sensors, and related hardware. Correct selection remains exact-application and exact-part-number specific.

Related Brembo Products

• Brembo KT00572 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Ceramic Pads
• Brembo KT04221 OE Rear Disc Brake Kit 2000-2006 Audi TT Quattro Low-Met Pads
• Brembo OE 01-03 BMW 525i/97-00 528i/01-03 530i/97-03 540i Rear Disc Brake Kit

Browse the Brembo collection for related brake components.

Frequently Asked Questions

Will this Brembo part fit my 2015-2021 Mercedes-Benz C63 AMG S?
That application is listed, but confirm the front or rear position, factory brake package, rotor diameter and design, caliper type, wheel clearance, production split, and every Brembo application note before ordering.

Should brake components be replaced in axle pairs?
Friction parts are normally serviced in axle sets to maintain balanced braking. Follow the vehicle service procedure and inspect the opposite side, calipers, hoses, hardware, wheel bearings, and brake fluid before installation.

What should be checked before installing this Brembo part?
Compare every component and part number, verify wheel and caliper clearance, inspect mounting and sealing surfaces, measure rotor and hub runout when applicable, use specified torque values, bleed the system correctly, and follow the required bedding procedure.

Installation Instructions

Follow the current Brembo instructions and factory service information for this exact part number. Support the vehicle safely, compare all parts before removal, clean and inspect mounting surfaces, verify runout and wheel clearance, replace one-time hardware and seals as required, use specified torque values, bleed with the correct fluid, check for leaks and free wheel rotation, complete the required bedding procedure, and recheck operation before road use. Professional brake installation is strongly recommended.